Welcome to the Slammer Marine Fender Layout Configurator. It does two things: it gives you a priced quote for your dock, and it gives you the precise list of fenders to order at slammermarine.com. Enter your measured lengths, choose your fender family and color, and you'll have an itemized quote and the exact SKUs to order before you leave the page. Faces over 180" let you pick the layout that fits your priorities.
Every fender kit includes the fender, the track, and all required mounting hardware. All custom-length track is cut to your measurements by Slammer Marine — no field cutting required. Photos help us most — upload pictures of your docks and we'll confirm the spec and catch anything unusual.
To order, fill your cart at slammermarine.com to match your quote and check out — we build only what you purchase. Have a question? Use the Ask Slammer Marine button just below — you will receive a reply from a human. You can also call us at 800-295-3464 to leave a voice message, and a human will call you back the same day.
You have a saved configuration on this device.
✓ Saved on this device
Ask Slammer Marine a question
We'll reply to the email you provide. Sends to info@slammermarine.com.
📎
Attach photos, drawings & files
Optional. Upload site photos, dock drawings, or any file (images, PDF, Word, Excel, etc.) to help specify your project. These are attached to your request when you send it to Slammer Marine.
1
Is this for existing dock assets or new construction?
Existing dock assets
Retrofitting fenders to docks already in place
New dock construction
Fenders specified as part of a new build
2
Project details
Used to label your quote and work order. No account or contact info required.
Customer type
Residential
Private dock owner
Marina Slip
Individual slip within a marina
Commercial
Commercial or municipal facility
Fender family and color are chosen per face in the next step, so each dock face can be Standard, Standard Fleece, Small, or Small Fleece. Price varies by family and length (not color); Fleece is available in Shark Gray and Deep Green.
Special requests (optional)
e.g. mixing Fleece and Standard fenders within a single face, or any other special requirement. We'll review and confirm.
Track Selection (pilings always use Polymer piling track)
Aluminum track is recommended for docks exposed to open water or active sea state, where loads are higher. Polymer is well suited to protected, calmer locations and is a single universal part.
Aluminum
Recommended for open-water / active sea state · Standard [S] + loader [L] sections
Polymer
Best for protected / calmer water · single part, every section is load-capable
3
Which fender system(s)?
Select any that apply. Standard and Small fenders cover dock faces (choose Fleece as a cover option per face); piling fenders cover vertical structures and pilings.
Standard Fender
9"H × 6"D tear-shaped profile — flagship product, mid to large vessels
Small Fender
Lower-profile dock-face fender — smaller vessels and lighter-duty faces
Piling Fender
5"W × 3.5"T — purpose-built for vertical structures and pilings
Add a row for each piling fender length. Different pilings can require different lengths. Standard lengths are 40", 80", and 120"; custom lengths run from 30" to 119".
4
What type of dock are you fendering?
Fixed dock
Permanently attached to land — does not float
Floating dock
One or more floating sections
Both
Fixed dock with floating sections attached
5
How many separate dock faces require fendering?
A dock face is any continuous straight run facing the water. Count each side separately. Do not count the side where a gangway or land connection attaches.
1
2
3
4
5
6
7
8
9
10+
6
Are any faces interrupted by a gap between floating sections?
Gaps between floating sections are not fendered. Each section is calculated independently.
No — each face is continuous
Yes — one or more faces have gaps
7
Enter the length of each dock face
Measure end to end along the water-facing edge in feet and inches. Do not add or subtract anything for corners. If a face has gaps, add each floating section in the series and the gap between them — gaps are not fendered or priced.
8
Do any faces require corner fenders?
No corners
Yes — corners required
Plan view (looking straight down). Outside corners use a corner fender that runs to the corner with a straight fender butting into its end; inside corners miter two inside pieces; aligned pairs match fenders directly across a slip.
For each face, choose which end(s) get a corner fender. Left / right are as you stand on the dock looking out over the water.
9
Layout for long faces
Any face over 180" needs more than one fender. Pick how each long face is divided. Faces 180" or under have a single fender and don't appear here.
Enter your face lengths above — long faces will show layout choices here.
10
Are any faces an aligned pair?
Two parallel fingers sharing a starting point. Pairing keeps the fenders directly across the water the same length until each face resolves its own run.
No
Aligned pair
Parallel fingers from a shared starting point — may be different lengths. Fenders directly across the water match in length from the shared start, until each face reaches its own length requirement.
↔
First selection is the reference. Each face keeps its own length; fenders across the water match until a face resolves its own run.
11
Dock structure & mounting
Aluminum track fastens to the fascia with 2″ #10 fasteners and needs at least 3″ of fascia height with solid structure behind it to attach to.
Fascia / dock material
Wood
Aluminum
Steel
Composite
Concrete
Solid structure behind the fascia to fasten to?
Yes
No / unsure
Protruding obstructions over 1/4″?
None
Yes
Rub rail / dock edging removed (or none present)?
Yes / none
Not yet
12
Save & send your quote
Enter a name for this quote and your email. When you generate, you can send the quote and shop work order to Slammer Marine.